Home     
 
 


   Top Subjects

CD Burners
CDs
DVDs
Radio
Television

Sponsored By:

   Categories
  
Arts
Games
Movies
Music
ShortStuff
Sports
Television
Toys
Browse the Entertainment Library

    
Main > Entertainment > Music

How CD Burners Work
by Tom Harris


 Introduction to How CD Burners Work
CD Basics
Reading & Writing CDs
Burning CDs
› Erasing CDs
CD Formats
Creating Your Own CDs
Lots More Information

Erasing CDs
In the last section, we looked at the most prevalent writable CD technology, CD-R. CD-R discs hold a lot of data, work with most CD players and are fairly inexpensive. But unlike tapes, floppy disks and many other data-storage mediums, you cannot re-record on CD-R disc once you've filled it up.

CD-RW discs have taken the idea of writable CDs a step further, building in an erase function so you can record over old data you don't need anymore. These discs are based on phase-change technology. In CD-RW discs, the phase-change element is a chemical compound of silver, antimony, tellurium and indium. As with any physical material, you can change this compound's form by heating it to certain temperatures. When the compound is heated above its melting temperature (around 600 degrees Celsius), it becomes a liquid; at its crystallization temperature (around 200 degrees Celsius), it turns into a solid.


In a CD-RW disc, the reflecting lands and non-reflecting bumps of a conventional CD are represented by phase shifts in a special compound. When the compound is in a crystalline state, it is translucent, so light can shine through to the metal layer above and reflect back to the laser assembly. When the compound is melted into an amorphous state, it becomes opaque, making the area non-reflective.

In phase-change compounds, these shifts in form can be "locked into place": They persist even after the material cools down again. If you heat the compound in CD-RW discs to the melting temperature and let it cool rapidly, it will remain in a fluid, amorphous state, even though it is below the crystallization temperature. In order to crystallize the compound, you have to keep it at the crystallization temperature for a certain length of time so that it turns into a solid before it cools down again.

In the compound used in CD-RW discs, the crystalline form is translucent while the amorphous fluid form will absorb most light. On a new, blank CD, all of the material in the writable area is in the crystalline form, so light will shine through this layer to the reflective metal above and bounce back to the light sensor. To encode information on the disc, the CD burner uses its write laser, which is powerful enough to heat the compound to its melting temperature. These "melted" spots serve the same purpose as the bumps on a conventional CD and the opaque spots on a CD-R: They block the "read" laser so it won't reflect off the metal layer. Each non-reflective area indicates a 0 in the digital code. Every spot that remains crystalline is still reflective, indicating a 1.

As with CD-Rs, the read laser does not have enough power to change the state of the material in the recording layer -- it's a lot weaker than the write laser. The erase laser falls somewhere in between: While it isn't strong enough to melt the material, it does have the necessary intensity to heat the material to the crystallization point. By holding the material at this temperature, the erase laser restores the compound to its crystalline state, effectively erasing the encoded 0. This clears the disc so new data can be encoded.

CD-RW discs do not reflect as much light as older CD formats, so they cannot be read by most older CD players and CD-ROM drives. Some newer drives and players, including all CD-RW writers, can adjust the read laser to work with different CD formats. But since CD-RWs will not work on many CD players, these are not a good choice for music CDs. For the most part, they are used as back-up storage devices for computer files.

As we've seen, the reflective and non-reflective patterns on a CD are incredibly small, and they are burned and read very quickly with a speeding laser beam. In this system, the chances of a data error are fairly high. In the next section, we'll look at some of the ways that CD burners compensate for various encoding problems.

 

1. Combo Drive DVD+RW/+R DVD-RW/-R 4.7GB INT EIDE 4X-DVD+RW+R 24X-CDRW
2. Dual DVD+RW/+R DVD-RW/-R (16x/10x/40x CDRW) - OEM
3. DVD+/-R/RW 8X/4X/12X DVD WRITE/DVD RE-WRITE/DVD READ
4. DVR-106 4X DVD-R/RW & DVD+R/RW DVD Burner
5. Dual Drive DVD+/-RW+/-R 4X2.4X 12 CDRW 16X10X32 INT IDE BLK/Silver

 
<< Prev Page    Intro    Next Page >>

  HSW Home


Table of Contents:
Introduction to How CD Burners Work
CD Basics
Reading & Writing CDs
Burning CDs
› Erasing CDs
CD Formats
Creating Your Own CDs
Lots More Information


 
Search Google:
powered by Google  
Rate this Article!
 


Copyright � 1998-2003 Howstuffworks, Inc. All rights reserved.

Lycos (R) s a registered trademark of Carnegie Mellon University.

Privacy Policy | Children's Privacy Notice | Terms and
Conditions |  Standard Advertising Terms and Conditions